Third-party or custom power supply

May 2007

Caution: Any damage caused to a Juniper Systems product by the use of an unauthorized third-party or a custom-built power supply is not covered by the standard product warranty. Information below related to finding a compatible third-party power supply or creating a custom power supply shall be used at your own risk.

 

Standard Power Supplies

 

We recommend using the standard power supplies (e.g., wall charger, cigarette lighter adapter, power dock, rechargable battery, external battery charger, legacy Allegro AA alkaline battery holder, HarvestMaster System Power Cable) that are shipped with the product or that can be purchased as optional accessories from Juniper Systems or an authorized product reseller. These standard chargers have been certified with our products in many countries to comply with radio noise/interference and power requirement laws.

 

Extended Battery Life

 

For more information about recommended options for extending the battery life of your Field PC, please visit our "Extended battery life" FAQ website.

 

Charging Port

 

It is highly recommended to only connect a custom third-party external power supply to the charging port of the Field PC (not directly to the battery terminals or otherwise). High currents should not be applied to any other ports or card slots of the Field PC.

 

Note: Limited power can be supplied to accessory devices from the Field PC through some of the ports and card slots. For more information, please visit our "Powering devices through bottom ports" or the legacy "Power supply for accessories through ports and card slots" FAQ web pages.

 

The specifications of the charging port on the Juniper rugged handheld computer are as follows:

 

  • 12 to 24 V DC at 1.67A (20W) or higher (12V at 800mA for legacy models)
  • 2.1 mm diameter inside barrel (positive terminal)
  • 5.5 mm diameter outside barrel (negative terminal)

 

Please refer to the image below for more information on legacy model chargers (which are fairly consistent with newer chargers).

 

VDC

 

If you can not obtain a connector that fits properly in the charging port of the Field PC, you can modify a vehicle (cigarette lighter) charger that can be purchased from Juniper Systems or a product reseller.

 

Power Requirements

 

The Field PC usually requires around 800mA (.8 Amps or ~10 watts) from the attached 12-24V (only up to 20V on legacy models) power supply for operation, with more for charging the battery pack(s). Make sure the power supply can provide a minimum of 800mA to ensure the Field PC does not exceed the maximum output of the power supply.

 

The HarvestMaster harvest data system sometimes requires up to 4A at 12V DC, depending on the actuators being used on the attached bucket system. We recommend using the newer, black power cable that has a right-angle connector. If you are using the old, thinner black power cable (without a right-angle connector) at lengths greater than 10 feet, voltages may sag, potentially affecting the accuracy of moisture readings.

 

External Batteries

 

If you do not have access to an auxiliary (cigarette lighter) port on a vehicle for connecting the standard Field PC vehicle charger, or if you are connecting a HarvestMaster system, the positive and negative terminals of a vehicle (lead-acid) 12V or 24V DC battery can be connected directly to the Field PC`s charging port, or to the HarvestMaster system power supply cable.

 

WARNING: If connecting to a battery that is also being used to operate the vehicle, make sure the battery does not drop below 10V or jump to above 18V during activities such as starting or shutting down the vehicle. This could potentially damage your Juniper Systems product or effect normal operation. Though our products have power protection circuitry, disconnecting the Juniper Systems product(s) during such activities or installing a 10 or 15 amp fuse may be the safest option.

 

Other battery types and chemistries (such as large gel cel camcorder batteries) may also be used as long as they meet the power requirements of the Juniper Systems product. For more information about battery types and chemistries, please visit the Battery University website.

 

Other potential power sources may include solar panels, generators (pedal, crank, etc.), and many others. Make sure that any power source you use meets the above mentioned specifications before connecting to a Juniper Systems product.

SNOWGAGE

HARVESTMASTER

JUNIPER SYSTEMS

CEDAR PRODUCTS

JUNIPER ASPECT

DIVISIONS

Juniper Systems &

HarvestMaster Main Office
_____

1132 W 1700 N

Logan, UT 84321 U.S.A.

Tel: 435.753.1881

Fax: 435.753.1896

Juniper Systems, EMEA

Main Office
_____

1st Floor

4 The Courtyard

Buntsford Gate, Bromsgrove

B60 3DJ, UK

Tel: +44 (0) 1527 870773

HarvestMaster Europe

Main Office
_____

Bauernstrasse 9, 4600

Wels, Austria

Tel: +43 7242219333

Email: office@harvestmaster.eu

SOCIAL

juniper blog

linkedin

youtube

facebook

twitter

SITE MAP

Copyright © 2018 Juniper Systems Inc. All rights reserved.